Epoxy flooring · Buckeye
Epoxy Shop and Garage Floors in Buckeye, AZ
Published
Orange Coatings coats garage floors and detached shop floors in Buckeye with Sherwin-Williams epoxy floor systems. Each slab is cleaned, degreased, repaired and profiled first, and the coating can include decorative flakes, a clear topcoat and an anti-slip additive.
Buckeye covers more ground than almost any city in the state, and a lot of its properties have room for a second building. Those shop slabs are often a different animal from the attached garage, and we treat them that way.

| Buckeye ZIP codes | 85326, 85396 |
|---|---|
| Population | 91,502 at the 2020 census (6,537 in 2000) |
| City area | About 393 square miles, second-largest in Arizona |
| Floors we coat | Attached garages, detached shops, RV and boat bays, home gyms |
| System | Sherwin-Williams epoxy floor coating plus flake, topcoat and anti-slip options |
| License | AZ ROC 365464 |
Shops, RV bays and outbuildings
Buckeye is Arizona's second-largest city by area, at about 393 square miles, and it is the westernmost suburb in the Phoenix metro. Out past the newer subdivisions, plenty of homes sit on lots with a detached shop, an RV garage or a metal building for equipment.
Those buildings carry heavier, dirtier work than a typical two-car garage. A coated shop floor sheds oil and grease, sweeps clean after a dusty day, and makes a dropped bolt easy to spot. It also stops the fine concrete dust that bare slabs shed onto tools and stored vehicles.

Outbuilding slabs and hidden moisture
Many shop and barn slabs were poured without a vapor barrier underneath. That matters, because moisture moving up through concrete is a leading cause of epoxy blistering and lifting. A slab can look bone dry on top and still push vapor into a coating once it is sealed over.
So we check those slabs before we quote the coating. A simple first test is taping a square of plastic sheet to the floor and looking for dampness under it after a day. If moisture is present, a moisture-mitigating primer goes down before the epoxy, and you know that before work starts rather than after the floor fails.
Garage, shop or both
Shop floors are often bigger than the house garage, with wider door openings and floor drains. We measure each building separately, note drains and anchor bolts, and list the house garage and the shop as separate lines on the quote so you can do one now and the other later.
Doing both in one trip saves a second setup. It also means both buildings are out of use at the same time, so think about where vehicles and equipment will sit while the floors cure.
Equipment that is hard on a floor
- Tractors, mowers and ATVs that track in dirt and gravel: sweep often so grit does not scratch the topcoat
- Jack stands and trailer jacks: set them on wood or steel pads to spread the load
- Welding and grinding: lay a welding blanket down, since sparks and hot slag can scorch any floor coating
- Fuel, oil and coolant: the topcoat keeps them on the surface, so wipe them up instead of letting them sit
- Washing vehicles indoors: add the anti-slip additive where the floor stays wet
From bare slab to finished shop floor
- Walk the building with you and check the slab for cracks, oil, old coatings and moisture.
- Degrease and clean, treating heavy oil spots so they do not bleed through.
- Repair cracks, chips and low spots.
- Profile the concrete so the coating can bond into it.
- Prime with a moisture-mitigating product if the test called for it.
- Apply the Sherwin-Williams epoxy base coat, flakes if chosen, and the clear topcoat.
- Let it cure, then walk the floor together before you move equipment back in.
Timing the job in an uninsulated building
A metal shop with no insulation can run hotter inside than the air outside on a summer afternoon. That heat shortens the working time of a two-part epoxy and can make it set before it levels. For uninsulated buildings, spring and fall are the easiest seasons, and summer jobs start at first light.
Every coat goes down inside the temperature and humidity limits on the Sherwin-Williams label. If the building is outside that range on a given day, we reschedule rather than force it.
New homes in Verrado and the growth corridors
Buckeye went from 50,876 people in 2010 to 91,502 in 2020, and it was named the fastest-growing city in the country for 2017, 2018 and 2021. That means a lot of brand-new attached garages in Verrado and the other master-planned areas.
New slabs need to meet the coating's minimum age and moisture limits, and they still get ground because builder concrete is troweled smooth. Coating right after move-in, before the garage fills up, keeps the job simple.
Ask your builder for the pour date. It tells us right away whether the slab is ready or needs more time.
Living with dust at the edge of the metro
Open desert, dirt roads and construction sites mean dust gets into every building out here. A flake broadcast in a mid-tone blend hides it far better than a solid color, and a clear topcoat lets you dust-mop or blow the floor clean in minutes. Good door sweeps help too.
A soft push broom or dust mop is better than a stiff bristle broom, which drags fine grit across the topcoat and dulls it over time.

Photos



Frequently asked questions
- Can you coat a detached metal shop floor in Buckeye?
- Yes. We check the slab for moisture and oil first, since many shop slabs have no vapor barrier, then prep and coat it the same way as a garage.
- Will epoxy hold up under a tractor or skid steer?
- A well-bonded epoxy with a clear topcoat handles rubber-tired equipment. Steel tracks, dragged implements and heavy point loads will damage any coating, so pad jacks and avoid dragging steel.
- Can I weld in a shop with an epoxy floor?
- Yes, but protect the floor. Sparks and hot slag can scorch the coating, so lay a welding blanket under the work.
- What if my shop slab has moisture coming up?
- We use a moisture-mitigating primer under the epoxy when testing shows it is needed. Skipping that step is a common reason shop floors blister.
- Is it worth coating the floor of an RV garage?
- For many owners, yes. It seals the concrete against drips from generators and holding tanks, and it makes the big floor much easier to keep clean.
- Do you travel that far west?
- Yes. Buckeye is one of the cities on our service list, and the estimate is the same in-person, same-day visit.
- Can I keep fertilizer and pool chemicals on the coated floor?
- Keep them on shelves or in trays rather than right on the floor. Spills wipe off the topcoat if caught early, but chlorine or fertilizer left sitting can stain or etch it.
Related
- Epoxy flooring
- Painters in Buckeye, AZ
- Shop and garage epoxy in Waddell
- Epoxy floor coatings in Goodyear
- Epoxy garage floors in Surprise
- Driveway coatings in Buckeye
- New construction painting in Buckeye
- How to prepare for new construction painting
- Why garage epoxy peels in Arizona
- Painting services by city
- Photo credits