Orange Coatings LLC · (602) 932-3417 · Get an estimate

Industrial painting · Arcadia

Industrial-Grade Painting and Coatings in Arcadia, Phoenix

Published

Arcadia is a residential neighborhood, so the industrial painting we do here is on a smaller scale: steel gates and fencing, detached workshops and garages, pool equipment enclosures, metal outbuildings, and the service areas behind shops along Camelback Road. Those surfaces need the same degreasing, rust removal and substrate-matched primers as industrial steel, even when they sit beside a family home.

Orange Coatings uses commercial-grade Sherwin-Williams products for this work and starts with a same-day, in-person estimate at your property.

Arizona Falls on the Arizona Canal, near Arcadia in Phoenix
Arizona Falls on the Arizona Canal, near Arcadia in Phoenix Photo: Alan Levine, CC BY 2.0, via Wikimedia Commons (resized)
Quick facts
NeighborhoodArcadia, in Phoenix and Scottsdale
Boundaries44th Street to 68th Street, Camelback Road to the Arizona Canal
SettingSouth foot of Camelback Mountain
Typical workSteel gates, workshops, pool equipment areas, service enclosures
CoatingsCommercial-grade Sherwin-Williams systems
LicenseAZ ROC 365464, bonded and insured

Why a residential property might need industrial coatings

The neighborhood runs from 44th Street to 68th Street and from Camelback Road north to the Arizona Canal, at the south foot of Camelback Mountain. There are no warehouse districts here. What there is, on many larger lots, is a lot of exposed metal and concrete that ordinary house paint does not handle well.

Steel that sits in sprinkler spray, a workshop floor that takes oil drips, a pool equipment pad full of chemical fumes: each of these needs prep and coatings closer to what we use on commercial and industrial buildings than to a typical repaint.

Detached workshops, garages and metal outbuildings

Many properties have a detached garage, studio or workshop, and some have steel or metal-panel outbuildings. Steel doors rust at the bottom edge, metal panels chalk in the sun, and concrete floors stain. We degrease and remove rust before priming, wash chalk off panels before recoating, and treat each material with its own primer.

  • Steel roll-up and swing doors on workshops
  • Metal-panel sheds and storage buildings
  • Block walls inside garages and studios
  • Workbench areas and floors that take oil and solvent spills
Paint tray and five-gallon bucket set on a drop cloth before a job
Paint tray and five-gallon bucket set on a drop cloth before a job

Steel gates, fences and pool equipment enclosures

Heavily watered yards keep fence posts and gate bottoms damp, and rust starts there long before it shows up higher on the steel. Pool equipment areas add chlorine fumes, which attack metal doors, pipe supports and screen enclosures.

Our process for both is the same in principle: degrease, remove loose rust and flaking paint down to sound material, prime bare steel the same day, and brush extra coating onto welds, hinges and bottom rails. Fixing the sprinkler that soaks the gate does more for the paint than any product.

Service areas behind shops along Camelback Road

The commercial strips on the neighborhood's southern edge have their own industrial-style surfaces, mostly out of sight. Trash enclosures, steel service doors, gas meters, conduit, rooftop screens and bollards take abuse from trucks, bins and weather. Business owners usually want those areas repainted quickly and with minimal disruption to the storefronts.

  • Block trash enclosures and their steel gates
  • Rear service doors and frames
  • Bollards and curbs in safety yellow
  • Exposed conduit and gas lines in the building color
Orange Coatings painter cutting in around a commercial doorway under an exit sign
Orange Coatings painter cutting in around a commercial doorway under an exit sign

Industrial-grade does not have to look industrial

A rust-inhibiting system on a front gate can still be finished in the soft black, bronze or deep green that suits the house. On block and workshop walls, we match the main house colors so outbuildings look like part of the property. The difference is in the prep and primer underneath, not in how the finished surface looks.

Sheen matters too. A satin or semi-gloss finish on steel sheds dust and water better than flat paint and wipes clean, while a flat finish on block hides small flaws in the texture. The estimate names a sheen for each surface so there are no surprises.

Workshop and garage floors

A workshop floor gets cleaned, degreased, repaired and profiled, then a Sherwin-Williams epoxy floor system goes down. Decorative flakes and a clear topcoat give a finished look, and anti-slip additive is an option near doors and sinks. If the slab was poured without a vapor barrier, we test it for moisture before coating; water vapor pushing up from below lifts epoxy off from underneath.

Garage floor finished with a decorative flake epoxy coating and clear topcoat
Garage floor finished with a decorative flake epoxy coating and clear topcoat

Protecting landscaping, pools and neighbors

Residential lots leave little room for overspray. Pools, mature plants, cars and the house next door all sit close to the steel we are coating. We spray only in calm air with screens and covers in place, cover the pool surface or brush near it, and keep pets inside until coatings are dry. Products with strong odors are used only where the space can be ventilated.

Summer heat matters here as much as anywhere in the Valley. Steel gates in direct sun get too hot to coat by mid-morning, so summer jobs start early, and monsoon season, June 15 to September 30, brings weather days.

Photos

Paint tray and five-gallon bucket set on a drop cloth before a job
Paint tray and five-gallon bucket set on a drop cloth before a job
Orange Coatings painter cutting in around a commercial doorway under an exit sign
Orange Coatings painter cutting in around a commercial doorway under an exit sign
Garage floor finished with a decorative flake epoxy coating and clear topcoat
Garage floor finished with a decorative flake epoxy coating and clear topcoat

Frequently asked questions

Is industrial painting relevant for an Arcadia home?
For certain parts of the property, yes. Steel gates, workshops, metal outbuildings and pool equipment areas need industrial-style prep and primers to hold up, even on a residential lot.
Can my detached workshop get an epoxy floor?
Yes, once the concrete has been scrubbed of oil, patched and mechanically roughened so the coating can grip. Flakes, a clear topcoat and anti-slip additive are options.
What holds up best on a steel gate that gets hit by sprinklers?
Thorough rust removal, a rust-inhibiting primer on bare steel and a durable finish, plus redirecting the sprinkler. Without fixing the water, rust will return at the bottom rail first.
How often should steel gates and fences be repainted?
It depends on sun, water exposure and how well the steel was prepped last time. Checking bottom rails and welds once a year and touching up small rust spots early stretches the time between full repaints considerably.
Do you paint trash enclosures and service doors for businesses on Camelback Road?
Yes. Block enclosures, steel gates, rear doors, bollards and exposed conduit are all common small industrial jobs, and we schedule them around business hours.
Will you protect our pool from overspray?
Yes. We spray only in calm conditions with covers and screens, and we brush and roll near the water when needed.
Do you work on the Scottsdale side of the neighborhood as well?
Yes. Arcadia spans parts of Phoenix and Scottsdale, and both are in our service area.

Related

Sources