Orange Coatings LLC · (602) 932-3417 · Get an estimate

Industrial painting · Buckeye

Industrial and Metal Building Painting in Buckeye, AZ

Published

Orange Coatings paints industrial buildings across Buckeye, from new warehouses near I-10 to metal shops, equipment barns and pump houses out in the farm country west and south of town. Each gets a coating system matched to its surface, from commercial-grade Sherwin-Williams lines, after a same-day, in-person estimate.

The two halves of the city need different things. New construction needs coordination with the builder; older metal buildings need rust repair and the right primer for galvanized or factory-finished steel.

Historic downtown Buckeye on Monroe Avenue
Historic downtown Buckeye on Monroe Avenue Photo: Marine 69-71, CC BY-SA 4.0, via Wikimedia Commons (resized)
Quick facts
City area393.2 square miles, Arizona's second largest city by area
Population91,502 (2020), up from 6,537 in 2000
ZIP codes85326, 85396
Elevation1,076 feet
Work we do hereMetal buildings, tilt-up, steel structures, shop floors
Contractor licenseAZ ROC 365464, bonded and insured

One city, two kinds of industrial work

Buckeye was the fastest-growing city in the United States in 2017, 2018 and 2021, and it is the westernmost suburb in the Phoenix metro. The growth shows up as new subdivisions, schools and logistics buildings near the freeway. Head farther out and the landscape is still fields, equipment yards and pre-engineered metal buildings, many of them decades old.

We paint both. A brand-new tilt-up warehouse and a sun-faded steel hay barn are very different jobs, so the estimate starts with what the building is made of and how it has held up.

Repainting a faded metal building

Factory-finished metal panels chalk and fade after years of desert sun. They can be repainted, but the chalk has to come off first, or the new coat bonds to powder instead of panel. We wash the panels, test adhesion on a small area, and use a bonding primer where the old finish is slick or weathered.

  1. Wash panels top to bottom to remove chalk, dust and bird droppings.
  2. Replace or tighten loose fasteners and treat rusted screw heads.
  3. Scrape, wire-brush and spot-prime rust along seams and the base of the wall.
  4. Test-patch the primer and finish on one panel and check adhesion before the full job.
  5. Apply the finish coats, working with the panel ribs rather than across them.

Galvanized steel needs a different primer

A lot of farm and utility steel is galvanized: gates, fence posts, stanchions, conduit and some building frames. Zinc reacts with certain oil-based paints and can break them down from underneath, a failure called saponification, which shows up as sheets of paint peeling off clean metal. New galvanizing also has a smooth surface that resists bonding.

The fix is cleaning the zinc thoroughly and priming with a product that is labeled for galvanized steel. Old galvanizing that has rusted through gets treated as bare steel: rust removed, then primed.

Where rust starts on Buckeye buildings

Catching rust at these spots early costs far less than replacing panels later. A walk around the building once a year, looking at the base, the fasteners and the gutters, tells you when touch-up is due.

  • The base angle where wall panels meet the slab and dirt and irrigation water collect
  • Screw and bolt heads, especially where washers have failed
  • Cut edges of panels and flashing
  • Gutters and downspouts that hold standing water after monsoon storms
  • Steel columns where livestock, equipment or tires rub the paint off
  • Door tracks and the bottom of sliding barn doors

New warehouses on the I-10 corridor

On new industrial construction, painting is one trade on a tight schedule. Fresh concrete has to cure and its surface alkalinity has to come down before most coatings go on, so we follow the primer label's requirements rather than painting the week the panels are lifted. We work from the project spec, coordinate access with the general contractor, and finish with a punch list and closeout documents.

If the building will have coated floors, we sequence them after the overhead trades are finished so the epoxy is not scratched by lifts and dropped tools.

Shop floors in equipment yards

Tractor and truck shops on outlying properties usually have bare slabs that are dusty, stained and hard to sweep. Coating the slab with a Sherwin-Williams epoxy system, after cleaning, degreasing and profiling, leaves a floor that wipes clean instead of soaking up every leak. We add anti-slip additive near wash bays and doors, and check older slabs for rising moisture before we coat them.

Garage floor finished with a decorative flake epoxy coating and clear topcoat
Garage floor finished with a decorative flake epoxy coating and clear topcoat

Dust, distance and long summer days

Dirt roads and open fields mean dust, and fresh coatings collect it. On windy days we hold off on finish coats, and we wash again if a storm has blown grit onto a prepped surface. Monsoon season runs June 15 to September 30 and brings the worst of it.

Metal roofs and walls in full sun also get too hot to coat by late morning in summer. Plan exterior metal work for fall through spring if you can, and expect early starts if it has to happen in summer.

Paint tray and five-gallon bucket set on a drop cloth before a job
Paint tray and five-gallon bucket set on a drop cloth before a job

Photos

Paint tray and five-gallon bucket set on a drop cloth before a job
Paint tray and five-gallon bucket set on a drop cloth before a job
Garage floor finished with a decorative flake epoxy coating and clear topcoat
Garage floor finished with a decorative flake epoxy coating and clear topcoat
Orange Coatings painter cutting in around a commercial doorway under an exit sign
Orange Coatings painter cutting in around a commercial doorway under an exit sign

Frequently asked questions

Can you paint a metal barn or equipment building in Buckeye?
Yes. Metal buildings get washed, rust-treated at seams and fasteners, primed where needed and finished. We check how the existing finish is holding up first, because that decides which primer goes on.
Is it worth painting a faded metal building instead of replacing the panels?
If the panels are structurally sound and rust is limited to edges and fasteners, painting is usually the practical choice. Panels rusted through are a replacement job, and we will tell you which ones those are.
Do you work on new industrial buildings while they are under construction?
Yes. We work from the project spec and coordinate with the general contractor on access, sequencing and closeout. Concrete cure requirements on the primer label set the earliest date we can coat tilt-up walls.
What primer goes on galvanized steel?
One labeled for galvanized metal, applied after the zinc is cleaned. Some oil-based paints react with zinc and peel, so the primer choice matters more on galvanizing than on almost any other surface.
Do you cover the outlying parts of Buckeye?
Buckeye is one of our service areas, and that includes properties beyond the town center. Give us the address when you call so we can plan the same-day estimate.
Does a metal building out here need a special paint for the sun?
It needs an exterior finish rated for metal and full sun, applied over the right primer. Lighter colors also run cooler and show less fading on west and south walls, which matters on a building with no shade at all.

Related

Sources