Industrial painting · Avondale
Industrial Painting for Avondale Shops and Warehouses
Published
Orange Coatings handles industrial painting in Avondale for fabrication shops, repair bays, contractor yards and the warehouses along I-10. The hard part on these jobs is rarely the paint itself; it is getting oil, grease and shop grime off steel, block and concrete so the coating bonds.
We use commercial-grade Sherwin-Williams coatings matched to each surface, and we quote after a same-day walkthrough of your building rather than from a phone call.

| Population | 89,334 (2020 census), up from 35,883 in 2000 |
|---|---|
| Land area | 47.87 square miles |
| ZIP codes | 85323, 85392 |
| Common surfaces | Block walls, steel doors, racks, mezzanines, shop floors |
| Coatings | Commercial-grade Sherwin-Williams systems |
| Licensing | ROC 365464, bonded and insured |
Industrial work in a compact city beside Phoenix
Avondale covers under 48 square miles and borders Phoenix, so its industrial buildings sit close together and close to homes. You see older block shops with roll-up doors, auto and equipment repair, contractor yards, and newer warehouses near the freeway. Population more than doubled between 2000 and 2020, and the buildings put up early in that stretch are now due for their second or third coat.
Many of these properties are owner-operated. That shapes the job: the owner is also the person who needs the bays open on Monday.
Owner-run sites also tend to collect years of patch painting from whatever can was on the shelf, which shows up as blotchy walls and mismatched doors. Part of our estimate is sorting out which surfaces need full prep and which only need a cleaning and a fresh coat.
Why degreasing decides whether shop paint sticks
Paint will not hold on a film of oil, hydraulic fluid or exhaust residue, no matter how good the product is. A wall next to a lift or a parts washer can look clean and still be contaminated. Our crews never skip degreasing on metal, and in a working shop we treat block and concrete the same way.
- Scrub with an industrial degreaser, working from the dirtiest areas outward so grime is not spread.
- Rinse thoroughly so no cleaner residue is left behind.
- Run a water-break test: if water beads up instead of sheeting, the surface still has oil on it and gets cleaned again.
- Remove loose paint and rust once the surface is clean, so the tools do not grind grease into the steel.
- Prime within the window the primer label allows.
Block walls inside fabrication and repair shops
Bare concrete block is full of pinholes that trap dirt and make walls hard to wash. A block filler coat closes those pores, and the finish coats over it give a smoother surface that cleans off with a hose or a mop. Lighter colors also bounce more light around a bay with few windows.
Areas near welding or grinding get planned around. Sparks and wet coatings do not mix, so hot work in that bay stops until the coating has dried to the point its label allows.
Oil-soaked shop floors
Years of drips leave oil deep in the pores of a slab. Epoxy put over that oil releases in patches, usually right where vehicles park. We clean and degrease the floor, sometimes more than once, then profile the surface and repair cracks and spalls before applying a Sherwin-Williams epoxy floor system. If the slab is older, we test for moisture as well.
If a section of floor is too contaminated to hold a coating, we tell you at the estimate instead of finding out after it peels.

Steel inside and outside the building
- Roll-up and overhead doors, tracks and housings
- Steel man doors and frames, which rust first at the bottom edge
- Pallet racks, mezzanines and stair rails
- Exposed beams, purlins and roof deck
- Security fencing, gates and yard equipment shelters
- Pipe bollards around fuel, air and electrical equipment

Painting a small industrial business without losing workdays
Most owner-run shops cannot close for a week. A common plan is to prep during the week around the work, then paint bays on a Friday afternoon and Saturday so coatings have the weekend to dry. Exteriors can usually run during business hours with the work area coned off.
Recoat and return-to-service times come from the label on each product and change with temperature. We put those times in the schedule so you know when each bay can reopen.
Fumes, solvents and safety in a working shop
Some industrial coatings carry solvents, and shops are full of ignition sources: welders, grinders, heaters and pilot lights. Before any solvent-borne product goes on, we agree with you on what gets shut off, how the space is ventilated, and how long it stays that way. Employees working in other bays should know where the painted zone is and when it is safe to walk through.
Photos



Frequently asked questions
- Can you paint the inside of an auto repair or fabrication shop in Avondale?
- Yes. Walls, steel, racks and floors in working shops are a normal part of industrial painting. The main job is cleaning off oil and grime first, then scheduling so your bays reopen on time.
- Can an oil-stained shop floor still take an epoxy coating?
- Often it can, after deep degreasing and profiling. We look at the slab during the estimate, and if a section cannot be cleaned well enough to bond, we say so up front.
- Why does paint keep peeling off our steel doors?
- Usually it went over rust, mill scale or an oily film, or the bare steel was never primed. Stripping back to sound material, degreasing and priming bare spots fixes the cause rather than the symptom.
- Do you paint roll-up doors and their tracks?
- Yes. Door curtains, tracks and housings are cleaned, spot-primed where the steel is bare, and finished. Moving parts are protected so the door still runs when we are done.
- What wall color works best inside a repair shop?
- Lighter colors reflect more of the available light, which helps in bays with few windows and makes leaks and spills easier to spot. Many shops use a darker, more forgiving color on the lower wall where carts and tools hit it, with a light color above.
- How soon can a bay go back into use after it is painted?
- It depends on the coating and the temperature, and each product label sets the times. We plan around those times and tell you in advance when each area is usable.
- Do you travel to Avondale from Surprise for estimates?
- Yes. Avondale is one of our regular service areas, and estimates are same-day and in person.