Paint color · Sherwin-Williams
Passive (SW 7064): Near-Neutral Light Gray for Modern Rooms
Published
Passive (SW 7064) is a light gray that sits very close to neutral, with a slight cool lean that some people read as a hint of blue. We calculate its LRV at about 60 from the RGB values, so it keeps rooms bright and exteriors relatively cool.
Its strength is how little it adds: no beige, no obvious green, just clean gray. That suits modern and minimalist homes, offices and gray-and-white kitchens. In a house full of warm finishes, though, it can look cold, so context matters.
Color swatch: Passive SW 7064, #CBCCC9
| Color | Passive |
|---|---|
| Code | SW 7064 |
| Hex | #CBCCC9 |
| RGB | 203, 204, 201 |
| LRV | About 60 (calculated from the RGB values, not Sherwin-Williams' published figure) |
| Family | Light near-neutral gray, slightly cool |
How neutral is Passive?
Its RGB values (203, 204, 201) are almost identical, with blue only slightly lower. That makes it one of the more neutral light grays, without the warm base of a greige or the green of a gray-green.
In practice it borrows the temperature of the light. In cool light it looks slightly blue-gray; in warm light it looks soft and plain. Next to warm beige finishes, it reads noticeably cool.
Passive in north-facing rooms
North light makes it cooler and a little deeper, and in a small north room it can feel stark. Paired with warm wood, woven textures and warm-white bulbs, it becomes a calm, gallery-like backdrop.
In bright south and west rooms it reads as a crisp, light gray that stays clean through the day. That consistency makes it a reasonable whole-house color in homes with mostly white and gray finishes.

Passive on stucco in desert sun
In full Arizona sun it lightens toward a soft silver and can look close to an off-white gray. On shaded walls it keeps its true light-gray depth, which gives a gentle contrast between sunny and shaded planes.
It suits contemporary homes with flat roofs, black window frames and simple lines. With warm tan tile and buff block walls, its cool character can look out of place.
Good uses for Passive, from kitchens to offices
In a kitchen with white shaker cabinets, gray-veined quartz and stainless appliances, Passive gives just enough color to separate the walls from the cabinets. It keeps the space feeling clean without the yellow cast of a warm white.
In bathrooms with gray porcelain tile, it ties walls to floors so the room reads as one calm space. With beige tile, choose a warmer gray instead.
- Modern and transitional interiors with white, gray or black finishes
- Home offices and media rooms where a quiet backdrop helps
- Exterior body on contemporary stucco homes with cool or neutral roofing
- Commercial offices and reception areas that need a clean, neutral wall
Pairings for Passive
- Nebulous White (SW 7063), a coordinating color, for soft gray-white trim and ceilings
- Extra White (SW 7006) for crisp, bright trim
- Peppercorn (SW 7674) or Iron Ore (SW 7069) for doors, pop-outs and window frames
- Cyberspace (SW 7076) for a front door with a subtle blue depth
Passive with black and charcoal accents
A near-neutral light gray body with charcoal or black accents is a common modern exterior scheme. Passive suits it because it adds no undertone that could fight the dark color.
Dark accents in Arizona sun get hot and show fading, so limit them to doors, window frames, railings and small pop-outs rather than whole walls. Check with the manufacturer before painting vinyl windows or doors dark, since some materials are not rated for dark colors in strong heat.
LRV of about 60: heat and fading
Using the RGB values, we arrive at an LRV of about 60; Sherwin-Williams lists its own measured figure on the color page. Around 60 percent of visible light bounces back, so walls stay cooler than they would in mid-tone grays.
Neutral light grays fade gracefully. The color itself changes little, and age shows mainly as chalking and a slightly duller surface, especially on south and west walls.
Sheen and paint for Passive
On stucco we use Sherwin-Williams Emerald Exterior in two coats, sprayed and back-rolled, with Loxon masonry primer on bare or patched areas. A flat or low sheen gives a modern, even look on the body; satin or semi-gloss is best for doors and trim.
In a Passive living room or office we apply low-VOC Emerald Interior in eggshell, and in kitchens and baths we switch to satin.
Testing Passive
- Paint a large board and compare it with a warm gray so you can see how cool it is.
- Look at it in your north-facing rooms first; that is where it will feel coolest.
- Outside, check it in direct sun and in shade, next to your roof and window frames.
- In an HOA, confirm approval of the body and accent colors before work begins.
Frequently asked questions
- Is Passive a warm or cool gray?
- It is close to neutral with a slight cool lean. In north light it can look a little blue; in warm light it reads as plain, soft gray.
- Does Passive look blue?
- Some people see a faint blue in cool light or beside warm beige finishes. With white and gray finishes it usually looks like a clean, light gray.
- What trim goes with Passive?
- Nebulous White (SW 7063) is a coordinating soft white, and Extra White (SW 7006) gives a crisper edge.
- Is Passive good for an office?
- It is a good office color because it is quiet and neutral, letting furniture, art and screens stand out. It also works in commercial reception areas.
- Can I use Passive on a stucco exterior?
- Yes, especially on contemporary homes with charcoal or black accents. In full sun it looks lighter than the chip, close to a pale silver.
- Will Passive look cold with travertine floors?
- Next to beige travertine it can look cool and slightly blue. If warm finishes are staying, compare it with a warmer gray first.
- Is Passive a good whole-house color?
- It can be in a home with mostly white, gray or black finishes and decent light. In homes with warm floors and cabinets, a warmer light gray often flows better from room to room.