Paint color · Sherwin-Williams
Iron Ore (SW 7069): The Soft Black for Doors, Frames and Cabinets
Published
Iron Ore (SW 7069) is a soft black: a very deep charcoal that reads as black from a distance but has a gentler, slightly warm softness up close. We calculate its LRV at about 6 from the RGB values, near the bottom of the scale.
On Arizona homes it makes front doors, garage doors, window frames, shutters and railings look crisp against light stucco, and it is a favorite for cabinets and interior doors. Used across large sunny walls, it soaks up a lot of heat, so placement matters more than with almost any other color.
Color swatch: Iron Ore SW 7069, #434341
| Color | Iron Ore |
|---|---|
| Code | SW 7069 |
| Hex | #434341 |
| RGB | 67, 67, 65 |
| LRV | About 6 (calculated from the RGB values, not Sherwin-Williams' published figure) |
| Family | Soft black, a near-black charcoal |
Iron Ore's undertone
Its RGB values (67, 67, 65) are nearly equal, with blue a hair lower, which tips it ever so slightly warm. That is why it looks softer than a jet black and less blue than many charcoals.
Next to bright white trim it reads as black. Next to warm beige stucco it can look like deep charcoal with a slight brown-olive softness, and in strong sun it lightens to a deep slate.
Iron Ore in strong sun and in shade
At midday on a west-facing garage door it looks lighter than expected, closer to a deep gray. Under a covered entry, on a recessed front door or in the evening, it reads as a rich near-black.
That shift is part of why it looks good outdoors: it never looks flat or inky like a pure black can in shade. It works with light grays, warm whites, beiges and even tans, which makes it one of the more flexible dark accents.
What an LRV of about 6 means in Arizona
Calculated from the RGB values, Iron Ore's LRV is about 6; Sherwin-Williams publishes its measured figure on the color page. A surface that reflects only around 6 percent of visible light absorbs the rest as heat, so a sunny Iron Ore wall or door gets far hotter than one painted a light neutral.
Dark colors also show UV wear sooner. Sun-facing doors and frames can lighten and chalk over a few seasons, and touch-ups show more on deep colors. Planning for periodic refreshes of the darkest surfaces is part of using this color well here.
Doors, window frames and railings
A soft black front door is one of the easiest ways to sharpen a beige or gray house, and Iron Ore is gentle enough that it rarely looks harsh. On window frames, fascia and railings it outlines the architecture in a modern-farmhouse or contemporary style.
Metal railings and gates need rust removed and a proper metal primer before a finish coat. Vinyl products should only be painted this dark if their maker approves, since some vinyl can distort when it absorbs heat.
Iron Ore inside the house
In north-facing rooms it reads as a deep, slightly cool charcoal; in sunny rooms it softens. Interior doors, kitchen islands, lower cabinets, a fireplace surround, built-ins and stair railings all suit it.
Full rooms in Iron Ore are dramatic and work best in offices, media rooms or powder rooms with good lighting and lighter floors or furniture for contrast.

Where Iron Ore fits
- Front doors and garage doors on light stucco
- Window frames, fascia, shutters and metal railings
- Interior doors, kitchen islands and lower cabinets
- Fireplace walls, built-ins and powder rooms
- Not usually a full exterior body in Arizona because of heat and fading
Pairings for Iron Ore
- Extra White (SW 7006), a Sherwin-Williams coordinating color, for crisp trim
- Nebulous White (SW 7063), another coordinating color, for a soft gray-white body or trim
- Colonnade Gray (SW 7641) or Accessible Beige (SW 7036) as a light body color
- Clary Sage (SW 6178) or Tony Taupe (SW 7038) as a mid-tone partner on shutters or pop-outs
Sheen and paint for a soft black
Exterior surfaces get Sherwin-Williams Emerald Exterior from us, with Loxon masonry primer on bare or patched stucco and two coats, sprayed and back-rolled. On doors and frames, a satin finish looks rich without highlighting every dent; semi-gloss is tougher but shows flaws more.
For Iron Ore cabinets and interior doors we use low-VOC Emerald Interior in satin or semi-gloss, after thorough cleaning, sanding and priming.
Testing Iron Ore
- Paint a board and hold it in the doorway or against the garage door at noon and at dusk.
- Compare it beside a pure black sample to decide how soft you want the dark to look.
- Check it next to your body color, trim white and hardware finish.
- If you are in an HOA, confirm a dark door, frame or trim color is approved before painting.
Frequently asked questions
- Is Iron Ore black or charcoal?
- It is a soft black, a very deep charcoal that reads as black from a distance. Up close and in sun it looks softer than a pure black.
- Is Iron Ore warm or cool?
- It is nearly neutral with a very slight warm lean. Next to cool grays it looks a touch warm, and in north light it can look cooler.
- Is Iron Ore a good front door color in Arizona?
- Yes, it is one of the most versatile dark door colors for beige, gray and white homes. A sunny door will need refreshing sooner than a shaded one.
- What white goes with Iron Ore?
- Extra White (SW 7006) is a coordinating color for crisp contrast. Nebulous White (SW 7063) gives a softer gray-white look.
- How is Iron Ore different from Tricorn Black?
- Tricorn Black (SW 6258) is deeper and closer to pure black, with a calculated LRV of about 3 versus about 6 for Iron Ore. Iron Ore looks softer and slightly warmer.
- Can I paint my whole house Iron Ore?
- On a sun-exposed Arizona house it will get very hot and show fading quickly. Most homeowners use it for doors, frames and accents instead.
- Is Iron Ore good for kitchen cabinets?
- It is a strong choice for islands and lower cabinets. Pair it with light counters and good lighting, and use a satin or semi-gloss finish.