Pool deck coatings · Avondale
Pool Deck Coatings in Avondale, AZ
Published
When an Avondale pool deck is peeling, the fix is to remove every bit of coating that has lost its grip, repair and profile the concrete, and put down a coating system made for pool decks. Orange Coatings does that with slip-resistant Sherwin-Williams deck systems, and we look at the failure in person before quoting.
Avondale more than doubled between 2000 and 2010, growing from 35,883 to 76,238 residents, and reached 89,334 by 2020. Pools from that boom are now fifteen to twenty-five years old, and many of their decks have been recoated at least once, not always with the right product.

| Avondale ZIP codes | 85323 and 85392 |
|---|---|
| Population (2020) | 89,334 |
| City size | About 48 square miles, bordering Phoenix |
| Our coating | Sherwin-Williams pool deck system with built-in slip resistance |
| ROC license | 365464 (licensed, bonded, insured in Arizona) |
Reading a failed deck coating
How a coating fails tells you what went wrong, and what the next coat needs. These are the patterns we see most on decks of this age:
- Peeling in sheets: the last coat went over dust, chalk or a glossy old coat without profiling, so it never truly bonded
- Bubbles and blisters: moisture or heat trapped under a film that could not handle it
- Cloudy or white patches: a clear sealer that has trapped moisture or broken down in the sun
- Bare spots only along the waterline: normal wear from splash-out, chemicals and wet feet
- Slick, shiny surface: a regular paint or sealer with no slip-resistant texture

Why wall paint and garage-floor products fail on pool decks
A pool deck is one of the hardest surfaces around a house. It sits in full sun, gets soaked and dried every day, takes chlorine or salt splash, and is walked on barefoot. Exterior wall paint is not designed for foot traffic or standing water, and most clear sealers turn slippery when wet.
That is why the products sold for walls or garages often look fine for a summer and then peel. A deck system is built for traffic, water and sun, with texture in the coating so it keeps grip when wet.
Stripping it back the right amount
- Pressure wash and degrease the full deck.
- Scrape every edge of the failing coating until it stops lifting.
- Check what is left: tightly bonded coating can stay, loose or blistered coating goes.
- Repair cracks and patch chips, spalls and low spots.
- Profile the surface so the new system has a rough, clean surface to grab.
- Mask coping, tile, drains and pool equipment before coating.
Garden Lakes, Coldwater Springs and older neighborhoods
Avondale's neighborhoods span several decades. Garden Lakes and the areas near the old town center have some of the older pools in the city, often with an original textured cool-deck finish under a few layers of paint. Coldwater Springs, Rancho Santa Fe and the neighborhoods built in the 2000s more often have a single builder coat or a sealer that is wearing thin.
Many of these neighborhoods have HOAs. If yours does, check whether a deck color needs approval before we schedule the work.
Rental homes and turnover timing
If the house is a rental, a pool deck is often the first thing a new tenant or buyer notices out back. Coating between tenants is easiest because nobody needs the backyard. Most residential decks take two to four days to prep and coat, and light foot traffic is usually fine about a day after the last coat.
A light, neutral color hides dust and hard-water spots between cleanings, which helps on a property you are not at every week.
What a deck coating can and cannot fix
A coating restores the surface: color, texture, grip and protection from stains and splash. It bridges hairline cracks once they have been filled, and it hides old patches so the deck reads as one surface again.
It cannot level a slab that has sunk, stop a crack that is still moving, or cure a drainage problem that sends water toward the house. If we see one of those during the estimate, we tell you before you spend money on a finish. Sometimes the right order is a concrete or drainage repair first and the coating second.
Heat, color and comfort
At about 974 feet, Avondale sits low in the Valley and gets some of the hottest afternoons in the region. Dark deck colors soak up that heat. Light tans, grays and off-whites stay cooler under bare feet and are the colors we recommend for a deck used in summer.
We start summer jobs early, while the slab is within the temperature range on the product label, and we schedule around monsoon storms between June 15 and September 30.
More work in Avondale
Homes of the same age often need the driveway or exterior paint refreshed too. We quote each item separately at one visit.
Photos


Frequently asked questions
- Someone painted my Avondale pool deck and it is peeling. Can it be saved?
- Usually. The concrete underneath is often fine. We remove the failed coating back to a sound surface, repair and profile the slab, and apply a deck system made for pools.
- Do I have to strip the entire deck down to bare concrete?
- Not necessarily. Coating that is still tightly bonded can stay after profiling. Only loose, blistered or peeling material must come off, and we show you which areas at the estimate.
- What about the cloudy white sealer on my deck?
- Clear sealers that have trapped moisture or broken down in the sun often turn milky. That film needs to be removed or thoroughly profiled before a new coating will bond. We check how much of it is left when we visit.
- Can a deck be coated between tenants?
- Yes, and that is the easiest time. Most decks take two to four days, so tell us your turnover window when you call and we will see if the schedule fits.
- Do you work near Phoenix Raceway and south Avondale?
- Yes. We cover the whole city, north and south of Interstate 10, including the neighborhoods near the raceway. The estimate is in person, so give us your cross streets when you call (602) 932-3417.
- How do I keep the new coating from peeling like the last one?
- Proper prep is most of it, and that is our part. On your side, rinse the splash zone regularly, keep deck drains clear and avoid dragging heavy furniture. Plan a fresh coat every three to five years, before it starts to flake.